Stouffville, Ontario Canada (647) 962-1997 gwstudios@rogers.com M-F 8:30am - 2:30pm & 8:00pm - 11:00pm

Tag: box joints

Slapping some stain on the old girl.

greatwallstudiosLeave a Comment on Slapping some stain on the old girl.

It was sunny and plus thirteen for about 90 minutes earlier today, so I popped out to the wood shop and dashed some Walnut coloured Danish Oil Stain onto my youngest daughters new single bed frame for the cottage.

I started by spot sanding a few bits that didn’t get all the love they needed the first couple of go rounds, and then spent a few minutes dusting it off with the air compressor. Then I splish-splashed the Danish Oil rub on it with a very wet foam brush, and ran through a few clean rags wiping it off. I think I managed to avoid runs in the finish, but I’m sure there’s one someplace very visible that I couldn’t see while I was bustling away this AM.

Good thing it’s so light weight, I didn’t need to call for help to move the whole thing around while I worked. Rests on my bench easily enough. It’s times like these that I am thankful for all the space saving theatrics I’ve had to undertake recently. My old layout would never have been wide or clear enough for both the frame and me. No chance I could have freely walked all 360 degrees around it before. I could still do with the whole shop being a good 36 inches wider, but that’s a very expensive construction matter. Also not going to happen. No way I tear down walls, and add roof for just three feet. Plus the property line is right there and no municipal office would ever grant me permits to get closer than eight feet to the line. So I’ll do what I can with what I’ve got.

Side bar: I am toying with the idea of taking down the pre-built racking that looks kinda shifty, in favour of metal racks, and reclaiming higher up wall space, but I need to get rid of several stored doors, and car seats, strollers, and household junk before I do that. It needs careful planning. I could benefit a great deal from doing so, but it’ll cost me both time & money, and a fair bit of aggravation to boot. I’m thinking it over. But I digress.

The Pine bed frame is one inch thick, with box joints, and a slatted cross member design. The feet all screw on, and the slats screw down into their mortises for extra peace of mind. It’s light weight, and has been stained to a Walnut brownish tone. One single pass. I’m told with Danish Oil I could do multiples, but I find one wetly soaked coat works fine for me. It ain’t no heirloom quality piece but it should last a few years. I hope.

(Fig 1.) Pieces break down. 6 feet / 6 slats / 2 rails & 2 ends.
(Fig 2.) Hand scraped finish, but sanded to 100 grit. Very rustic appearance.
(Fig 3.) Assembled upside down. Original Pine colour showing.
(Fig 4.) Starting to Stain with it still upside down. Notice how much room I now have to get all the way around it! Ohh- Aah.
(Fig 5.) All stained up, drying & off gassing that nose prickling oil finish smell. Could stay in here for a few days getting that smell to dissipate.

Finishing isn’t exactly my favourite thing to do. It’s sticky, and smelly, and finicky too. My shop doesn’t have an air cleaner, nor do I use anything better than a shop vac to control the dust I make. Not good for high end, ultra high quality finishing. But I get it done regardless. Although now the temperature has plummeted down to minus one, and will go even lower and bring in some snow too. So I don’t know how anybody can plan around this type of thing. Well… a temperature controlled working space would alleviate those stressors, but I ain’t got that kinda dough just lying around for a quirk of mine.

So maybe a single spray on layer of Diamond Coat will go on next, or not. This piece may not be worth the additional effort. It will get scratched & marred. I’m none too concerned about that. If I can get a shot of it in situ up north I’ll update about the bed frame one last time. Take care out there. Ciao Bella.

The Pine Bed Episode. The one where I learn, again, not to leave projects for months on end and expect everything to fit as well as the day I made all the joinery in the first place.

greatwallstudiosLeave a Comment on The Pine Bed Episode. The one where I learn, again, not to leave projects for months on end and expect everything to fit as well as the day I made all the joinery in the first place.

The story up till now goes as follows; My youngest was in a crib at the cottage for a long time. Then I transformed said crib into a day bed, which she used until she was too long for it and spent all night kicking the end and side panels waking everyone up. I took the crib down and we pulled a single mattress into the room and set her up on the floor. With the intention of putting up a bed shortly there after. Things happened over the summer and the bed was forgotten about. Travel, funerals, anguish, and work took a front seat. Come to September and I milled down a few pine boards, cut them to size, made lots of tight fitting joinery, and then let it sit because I had other things to do and it wasn’t a priority. Fast forward from September to February and a warm spell and I finally had the time to sand it all down, and then I went ahead and began assembly and fitting it all together. Wood movement is a thing, and I continuously don’t pay enough attention to that fact and leave projects for months on end. Good news is, we are assembled. I need to do a few gap fill touch ups, and then a final sand in a few spots, and then stain it all. Let is stand & off gas for a few days then schlep it to the cottage in the back of a truck. It’s pine so it’s pretty light. Easy to move around, and lift up several sets of stairs.

Unsanded pieces.
Freshly sanded pieces.
Assembled while upside down. Waiting for box joint fixes, sanding and wipe on, wipe off stain.

It’s not the prettiest thing, certainly not heirloom quality, but one inch thick pine should hold up for a few years at least. Slatted to hold a box spring, or go straight over with a firm mattress. Would I have preferred to build it with Walnut or a hardwood, certainly I would, but it would be 10X the weight, and who knows how much extra in cost.

I put in an order for 20BF of Walnut last night from a company that delivers. Rough cut, one inch thick. Should come some time next week. I can then plan some narrow book shelves for my kids, and a new Urn. I’m going to try hand cut dove tails this time. I want to book match the outside so I’ll also need to cut some boards down the middle too. That will take some time. Sounds like fun!

I just can’t seem to find the time to get over to the mill to view lumber, so getting some delivered is really helpful. If the wood quality is a bust then I will have to do so myself, shop in person that is. I didn’t spend crazy money on it, so I’m not expecting glowingly perfect boards. A touch rustic perhaps, definitely straight with no cupping, or twist would suit me just fine.

I recently had the chance to use my wood moisture meter. Works great. Reminds me I need to charge and format my endoscope for the car. Has lights on it too! He-he.

We have the funeral today, so I need to fetch the kids from school, change, and head over to the visitation, and then the service proper, and then hang around after to take all of the decorations, flowers, and photos down. Hug your loved ones. Ciao Bella.